Asuka 120 LimitOver/Netplay: Difference between revisions
Jump to navigation
Jump to search
(/* Rollback with RetroArch) |
mNo edit summary |
||
Line 22: | Line 22: | ||
# In the sidebar, click on {{clr|9|Saturn}}, find & launch '''LimitOver'''. Select '''SEGA Saturn (Beetle Saturn)''' for the core. | # In the sidebar, click on {{clr|9|Saturn}}, find & launch '''LimitOver'''. Select '''SEGA Saturn (Beetle Saturn)''' for the core. | ||
#* If you don't find LimitOver in the list, it might shown as "Asuka 120% Limited", click on it, check {{clr|9|Information}} at the bottom & rename the correct file. | #* If you don't find LimitOver in the list, it might shown as "Asuka 120% Limited", click on it, check {{clr|9|Information}} at the bottom & rename the correct file. | ||
[[File:A120LO controls.png|thumb| Recommended Button layout]] | #: [[File:A120LO controls.png|thumb| Recommended Button layout]] | ||
# Press F1, {{clr|9|Control > Port 1 Controls}} | # Press F1, {{clr|9|Control > Port 1 Controls}} | ||
#* Assign the previously set RetroPad buttons (shown on the left) to the current console controller (on the right). | #* Assign the previously set RetroPad buttons (shown on the left) to the current console controller (on the right). |
Revision as of 11:27, 12 April 2024
Rollback with RetroArch
🧩 Setup
- Install RetroArch from Steam
- In Steam, Right click on RetroArch: Properties > Installed Files > Browse & put all files in "system" folder (if it doesn't exist, create it).
- Start RetroArch
- In the sidebar, select Import Content > Scan Directory, go to your ROM folder & click <Scan This Directory>.
- Settings > Latency
- Run-Ahead to Reduce Latency: OFF
- Settings > Input > RetroPad Binds > Port 1 Controls
- Map your input as your default xbox/PS controls, NOT the game input (btw Retroarch notation uses Nintendo's layout).
- Netplay > Network
- Use Relay Server: ON
- Relay Server Location: Custom
- Custom Relay Server Address: retro.supercombo.gg for US (East) / uk.yuribacon.com for EU
- ⚠️ If you don't see this, go to Settings > User Interface > Show Advanced Settings, toggle it ON.
- Netplay Check Frames: 0
- Input Latency Frames: 2
- Frames Range: 3
- Netplay > Lobby Filters set everything to ON.
- In the sidebar, click on Saturn, find & launch LimitOver. Select SEGA Saturn (Beetle Saturn) for the core.
- If you don't find LimitOver in the list, it might shown as "Asuka 120% Limited", click on it, check Information at the bottom & rename the correct file.
- Press F1, Control > Port 1 Controls
- Assign the previously set RetroPad buttons (shown on the left) to the current console controller (on the right).
- ⚠️ This part is NOT intuitive! Don't worry, it's not you, it's the emulator's fault. Press F1, to go back in game & test your buttons. Good luck.
- Once done, go to Control > Manage Remap Files > Save Remap File As so you never have to do this again.
- Now just set up your name in Settings > Users > Username and you're finally ready to play! ✨.
Host & Join
🌐 Host
- Netplay > Host > Start Netplay Host
- Start the game you want to host. Wait for your opponent ✨.
🌐 Join
- In Netplay > Refresh Netplay Host List
- Find your opponent in the list, click on them. Fight ✨.
- If your game doesn't start: boot up the game and retry.
- If you don't see a list: try to click Refresh LAN list then Resfresh host list again. If that doesn't do it restart RetroArch (sometimes restarting twice works too :V).